Choosing an LED Sign for Your Church

Know what to check before you buy, from local sign rules to installation and ongoing support.

  • ZoningPermits and local sign rules.
  • ReadabilityViewing distance, display size and pixel pitch.
  • BudgetMounting, power and installation costs.
Brick First Baptist Church monument sign in Nevada, Missouri, with a digital display showing a Sunday morning message. TAAG Church roadside sign shows an Easter event message on its LED display above a planted flower bed and landscaped lawn. Rocky River Presbyterian Church stone monument shows a Bible-verse message on its LED display beside the church grounds and trees.

Church sign buying guide

Start with what your church can install at your location.

Can we put up an LED sign at our church’s location?

Start with your local planning or zoning office. Give them the church’s street address and ask whether an electronic message display is allowed on that property. Churches are often in residential neighborhoods, where sign rules can be restrictive or prohibitive. Many zoning ordinances are designed specifically to ensure signage does not detract from the atmosphere of a residential neighborhood. Ask about setbacks, maximum height, whether a monument base is required, brightness, operating hours, and how often the message can change. Ask which drawings and approvals the office needs before anyone orders a display.

How far away will people read the sign?

Start where you expect people to first see the sign. Is that a sidewalk, the entrance drive or the far lane of a busy road? Measure the distance from those spots and check both directions of travel. At road speed, a driver needs time to spot the display, read the message and decide whether to turn. Trees, parked cars, curves and the angle of the display all matter. Ask your installer for a mockup from the road showing a real message such as “Sunday Worship 10 AM.” If the letters are too small, try fewer words, larger lettering or a larger display within the permitted size. Ask for the active display dimensions separately from the overall sign dimensions.

What pixel pitch do we need?

Pixel pitch is the distance between neighboring pixels, measured in millimeters. A smaller pitch puts more pixels into the same display area, which can make small lettering and faces look clearer up close. A larger pitch can work well for short messages in big letters viewed from farther away. The size of the display matters too, because it determines how many pixels you have to work with at a given pitch. If you want to show your pastor’s portrait or a guest speaker’s photo, send that exact image to your installer. Ask to see it alongside a service time on each proposed display size and pitch, at the distance people will actually view it. If the face is hard to recognize or the text has to shrink, try a tighter crop, put the photo and text on separate slides where local rules allow, or compare a finer pitch.

Should we use a monument, pole or wall mount?

Start with what your permit allows, then check the display from a driver’s line of sight. If your location requires a monument or caps the overall sign height at 8 feet, for example, work with your installer to position the LED display where drivers can see and read it within that limit. A display mounted too close to the ground can disappear behind parked cars or landscaping, even when the sign itself meets the height requirement. Ask for a drawing that shows the height of the LED display within the overall sign, including any base and identification cabinet.

Where other mounts are allowed, a pole mount may lift the display above obstructions. A wall mount can make sense when the building faces the intended audience and the wall can support the display. For any option, check the proposed height and angle from a driver’s eye level in both directions of travel. Make sure people can read the message before they pass the entrance.

Can we convert our changeable-copy sign to LED?

Possibly. If your church has a sign with manual changeable letters, you may be able to keep the identification cabinet and replace just the message area. Send photos of both faces and the full structure, plus the opening dimensions if you have them. Have your installer check the cabinet, supports, foundation, electrical supply and service access before assuming the structure can be reused. Ask whether the conversion needs a new permit. Compare a retrofit with a full replacement if the old cabinet needs major repairs or the opening is too small for readable messages.

What should we budget for beyond the LED display?

Build your budget around the installed sign. Ask for separate prices for the LED display, the cabinet or mounting hardware, site preparation, installation, permit drawings and fees, and electrical work. If you want a brick monument, ask whether the sign contractor includes the footing and masonry or whether the church needs to hire a brickmason. Get a price for the brick or matching veneer, delivery and labor. Ask who coordinates the mason, electrician and sign installer so everyone is pricing the same plan.

Check power before you settle on a location. Have an electrician confirm whether power is already there and whether the existing circuit can support the proposed display. A manual changeable-copy sign may have no power at all, or it may only have power for lighting. If you need new service, ask the electrician to price the route from the source to the sign, including any trenching, conduit and restoration of pavement or landscaping. Get that estimate early enough to compare locations if you have a choice.

For a replacement, ask for a separate price to disconnect, remove and dispose of the old sign and install the new one. Confirm which pieces can stay and whether any repairs are included. When you compare bids, ask each installer what the church must arrange or pay for separately. A lower display price can leave more of the project on your side of the ledger.

What should we confirm before approving the quote?

Ask when your sign will be installed, how long the installers expect to be on site, and what the church needs to have ready before they arrive. Ask which installation costs could change, what would trigger an extra charge, and how the installer will let you know before doing that work.

Compare warranties side by side. How long does each warranty last? If one quote says three years and another says five, check what each covers, including which parts and labor are included and for how long. Ask whether the manufacturer guarantees parts availability, for how long, and who can service the sign once the warranty ends.

Ask what training is included for the sign software and day-to-day operation. Have the staff or volunteers who will run the sign practice scheduling, editing and removing a message. Find out who to contact when you have a question or the sign stops working, how you can reach them, and what response time you can expect.

Planning a sign for your church?

Send us a photo of your existing sign and any requirements you already have. You can upload the photo when you request a quote.